EPDM Roofs in Wrexham
Need a flat roof with as few joins as possible?
EPDM membranes laid in one sheet where size allows, for Wrexham extensions and dormers.
CALL US HERE - 01244 740253GET A FREE ASSESSMENT


EPDM roofs in Wrexham mostly come down to one thing: seams. Every join on a flat roof is a place water can try its luck. EPDM comes in wide rolls, so on most garages, porches and extensions it goes down as a single sheet, cut to size. No joins across the middle to fail.
EPDM stands for ethylene propylene diene monomer. You don't need to remember that. What matters is that it's a rubber that stays flexible for decades, and it goes on cold, with adhesive rather than a gas torch.
If you're weighing it up against other systems, our flat roofs in Wrexham page puts them side by side. Our Wrexham page covers everything else we do in the area.
Where EPDM works on Wrexham properties
Rear extensions
Single-storey kitchen and utility extensions are the classic EPDM job. The membrane runs up the house wall behind a flashing, across the deck and down into a gutter trim at the edge. If there's a rooflight or lantern, we form the upstand around it so that detail stays watertight. Once the deck is ready, it's one of the quicker roofs we lay.
Dormers on loft conversions
Dormers on older terraces often have small flat roofs that are awkward to reach and take the full force of the weather. EPDM is light enough to carry up a ladder and can be fitted without a flame near timber cladding or the neighbour's roof. That makes it a tidy fit for a cramped, high-up spot.
Garages and outbuildings
A detached garage or a workshop at the bottom of the garden doesn't need anything fancy, just a roof that stays dry without attention. EPDM does that. It's a step up from felt in lifespan and only a modest step up in price. We'll help you pick a membrane grade to match how long you need the roof to last.

1,000+ Roofing Projects
Friendly & Reliable Team
EPDM and Wrexham's wet, changeable weather
Wrexham's weather swings about. Mild, wet westerlies come in off the hills for days at a time, then a clear night drops the temperature below freezing. Materials that expand and contract by different amounts end up pulling at their joins. EPDM moves as one sheet and stays flexible well below freezing, so cold snaps and heavy rain are less of a worry in the long run than they are with older felt roofs.
Dormers added to older terraced houses were often felted when they went in and have been patched since. They're a natural candidate for EPDM when the felt finally gives up. So are the flat-roofed garages that turn up on postwar estates across the city. Both are small, exposed roofs where a single sheet with no joins makes the most sense.
How we fit an EPDM roof
Survey
We check the deck, the joists where we can see them, the drainage and every wall the roof meets. You get a free written and verbal quote with the membrane grade spelled out, and what each grade would cost.
Deck and edges
The old covering is stripped and the deck checked. Soft boards are replaced with new OSB or ply. Timber battens are fixed around the edges to take the trims, and any falls are corrected so water drains to the outlet.
Lay and bond
The EPDM is unrolled and left to relax so it lies flat, then bonded to the deck with a water-based adhesive. The perimeter gets a stronger contact adhesive. Upstands are turned up the walls to a sensible height.
Trims, outlets and photos
Edge trims and gutter drips are fixed, outlets sealed and the wall detail finished under flashing. We send you photos and video along the way and finish with a guarantee covering materials and workmanship. Nothing gets left on the roof.
Why choose EPDM from our team in Wrexham
- One-piece membranes on most domestic roofs, so there are no seams across the middle to fail.
- Cold-applied with adhesive, with no torch on site near timber, cladding or a neighbour's roof.
- Light enough for older structures that couldn't take a heavier covering without strengthening.
- A choice of membrane grade, explained in plain terms with a price for each.
- Fitted by roofers with more than 25 years in the trade, and guaranteed on materials and workmanship.


What does an EPDM roof cost in Wrexham?
An EPDM roof is usually priced from about £1,500, and very few go past £4,000. The grade of membrane is the main variable, followed by size and the condition of the deck. Each rooflight, soil pipe or awkward corner adds a bit of labour, because those details take longer than flat runs of rubber.
On older terraces, an EPDM dormer can cost more per square metre than a big garage roof, even though it's smaller. That's down to access. A dormer may need scaffold at the front or back of the house, and every bit of material goes up by hand. A ground-floor extension with side access sits at the cheap end of the scale.
EPDM Roofs in Wrexham: Your Questions
Is planning permission needed for an EPDM roof in Wrexham?
Re-covering an existing flat roof in EPDM doesn't normally need planning permission. A listed building may still need listed building consent, and in a conservation area with an Article 4 direction, such as Salisbury Park or Fairy Road, check with Wrexham County Borough Council before changing anything visible from the street. Building Regulations may also require better insulation when a flat roof is replaced.
Will EPDM lift in the wind on an exposed house?
Not if it's bonded properly. The whole sheet is glued to the deck, with stronger adhesive round the edges where wind pressure is highest, and the perimeter is held down by trims. On exposed spots, like hillside houses facing west towards the Welsh hills, we pay extra attention to the edge fixings. That's where wind tries to get under any roof.
How quickly can you fit an EPDM roof in Wrexham?
Once the quote is agreed, we'll give you a date and order the materials straight away. Fitting is one of the quicker flat roof jobs because there's no curing time and no heat involved. The one thing we can't control is rain. The adhesives need a dry deck, so a wet Wrexham week can push the start back.
How long does an EPDM roof last?
Fitted well, EPDM can give you up to 40 years. When one fails early, it's rarely the membrane wearing out. It's poor detailing at the edges and upstands, or a deck that wasn't sound before the rubber went down. That's why most of our time on site goes into the preparation.
Can EPDM be repaired if it gets damaged?
Yes. A puncture from a dropped tool or a falling branch can be cleaned and patched with EPDM and the right primer and tape. It's a small job. Patching early stops water reaching the deck, which is where a cheap fix turns into a new roof. Our rubber roofs in Wrexham page covers the wider family of membranes.
What To Do In Wrexham

National Trust - Erddig
Learn More about National Trust - Erddig
Xplore! Science Discovery Centre
Learn More about Xplore! Science Discovery Centre
